StableLoad - Lower Overload with drill kit
Item # A7311
List Price: $515.58
Our Price:
$468.71
This StableLoad kit is designed installation on vehicles with lower overload springs that aren't predrilled from the manufacturer. The StableLoad Quick Disconnect DRILLING REQUIRED kit (part number A7311) is available for installation with amazing results. This kit comes with four specially treated drill bits and specific instructions for drilling the required (four) 3/8" diameter holes through the ends of the lower overload. The average time to complete the drilling process is approximately 35 minutes.
The StableLoad dramatically improves vehicle handling characteristics by "pre-activating" the stabilizing effect designed for rear springs by keeping them actively under load the way your vehicle factory engineers designed them to operate.
StableLoads are designed to improve the handling characteristics of your loaded vehicle by “pre-loading” the factory overload spring.
StableLoad Features
- Kit includes Four Stable Loads (outfits one complete truck)
- Dramatically improves safety, handling, body roll and porpoising while towing and hauling
- Ability to turn on and off in seconds*
- Universal fit for all vehicles with factory installed upper or lower overloads
- Quad contact design complements the vehicle’s specially engineered suspension that automotive manufacturers have invested millions of dollars designing, while all other rear suspension products reduce contact to only two points
- Quick no-drill installation**
- Enhances airbag performance by lowering airbag overload air pressure and activating the factory overloads
- Kit includes four StableLoads (outfits one complete vehicle)
- Legendary Lifetime Warranty includes coverage for the vehicle factory leaf springs
- Proudly made in the USA
* Applies only to the StableLoad Quick Disconnect (Lower Overload).
** Does not apply to the StableLoad Quick Disconnect (Lower Overload) A7311 (with Drill Kit).
Due to the dramatic improvement in overall handling characteristics from the StableLoad and its extremely low cost,* we recommend any suspension enhancement upgrades start with the StableLoad and that the vehicle operator evaluate as to whether any further upgrades are needed as often times the StableLoad suspension enhancement qualities are found to be more than enough improvement and no further costly suspension equipment may be required.**
* When compared to other suspension upgrade products, the StableLoad costs up to 50% less.
** Further upgrading or product additions for vehicle suspension is the responsibility and made solely at the discretion of the vehicle owner/operator.
The StableLoad Quick Disconnect (patented) is our number one recommended most effective and versatile StableLoad. This StableLoad design is specifically engineered for the extremely robust lower overload springs. The lower overload springs are generally over 30% stronger than upper overload springs making this StableLoad design the most effective. This StableLoad design offers astounding improvement in safety and vehicle handling and is accomplished by putting the robust lower overload to work sooner dramatically stabilizing the vehicles suspension making the vehicle's passengers and load significantly safer. All StableLoad kits work equally well with or without aftermarket airbags overloads.
The Quick Disconnect models for the lower overload spring incorporate a unique design that allows the StableLoad to quickly engage or disengage your lower overloads, enabling you and your passengers to ride in safety and comfort when towing or hauling and to quickly return to the original ride in just seconds when not towing or hauling. This is accomplished by attaching each of the StableLoads (four per kit) onto each overload end (front and rear passenger side, front and rear driver side). The Quick Disconnect StableLoad Series is designed with a tapered wedge mounted to a hinge mechanism that allows the StableLoad to be hinged in or out of engagement in seconds using a common 3/8" ratchet extension and ratchet. Each precision crafted StableLoad kit carries our Legendary Lifetime Warranty and is proudly made in the USA.
Manufacturer: Torklift
This product fits the following vehicles:
1999-2009 Ford F250, Regular Cab, 8' Bed, Super Duty with Factory Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F150, Regular Cab, 6.5' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F150, Regular Cab, 8' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F150, Extended Cab, 6.5' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F150, Extended Cab, 8' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F250, Extended Cab, 6.5' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F250, Crew Cab, 6.5' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F250, Regular Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F250, Extended Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1996 Ford F250, Crew Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1997 Ford F350, Extended Cab, 6.5' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1997 Ford F350, Crew Cab, 6.5' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1997 Ford F350, Regular Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1997 Ford F350, Extended Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1981-1997 Ford F350, Crew Cab, 8' Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1983 Ford Ranger, Regular Cab, 6.5' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1983 Ford Ranger, Extended Cab, 6.5' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1984 Ford Ranger, Regular Cab, 6' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1984 Ford Ranger, Extended Cab, 6' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Regular Cab, 8' Bed, Square Body Style, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Extended Cab, 6.5' Bed, Square Body Style, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Extended Cab, 8' Bed, Square Body Style, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Regular Cab, 6.5' Bed, Square Body Style, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Regular Cab, 6.5' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Extended Cab, 6.5' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Regular Cab, 8' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F150, Extended Cab, 8' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F250, Extended Cab, 6.5' Bed, Square Body Style, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F250, Regular Cab, 8' Bed, Square Body Style, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F250, Crew Cab, 6.5' Bed, Square Body Style, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F250, Extended Cab, 8' Bed, Square Body Style, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997-1999 Ford F250, Extended Cab, 6.5' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997 Ford F250, Crew Cab, 8' Bed, Square Body Style, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1997-1999 Ford F250, Regular Cab, 8' Bed, Round body, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1998-2009 Ford F150, Crew Cab, 5.5' Bed, Gas Engine, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1999-2008 Ford F250, Extended Cab, 8' Bed, Super Duty with Factory Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1999-2009 Ford F250, Crew Cab, 8' Bed, Super Duty with Factory Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drilling holes in the overload springs in the same factory locations found on vehicles with pre-drilled holes will have no affect on your spring's integrity or operation. The drilled springs (when drilled in accordance with the Torklift International drilling specifications) and the integrity of the springs once drilled are covered under the Legendary Lifetime Warranty. -Some overload springs may have adhesive padding on top of the overload spring, Use a screwdriver or equivalent to remove the padding. This will ensure proper rotation and ease of use.
- On Quick Disconnect StableLoad (part#'s A7310/A7311): Due to wear and tear after time, some vehicle leaf springs may have minimal clearance with the lower overload for StableLoad engagement / disengagement when the vehicle is unloaded. In order for the StableLoad to engage and disengage with minimal effort, a minimum gap of 1/8" is required between the lower overload and the spring pack.
1999-2008 Ford F250, Extended Cab, 6.75' Bed, Super Duty with Factory Bed, Gas or Diesel, 4X2 & 4X4
- No drilling required.
- A7311 (WITH DRILL KIT) will fit any passenger or commercial vehicle, van, SUV, truck, RV etc., with rear leaf springs and a lower overload spring. The lower overload leaf can be identified by being on the very bottom of the spring pack. It's thicker than the rest of the leaf springs in the spring pack usually has a gap between the lower overload leaf spring and the upper leaf spring pack.
-Drilling four 7/16 holes required. Specially treated drill bits and detailed drilling instructions are included.
-Average drill time is 30-40 minutes for complete installation
-Many factory overload springs come pre-drilled with 1/2" holes. Drillin
Click image below for detailed installation instructions:
